:::현재위치 HOME ▶ 중고제품 ▶ Calibrator/SourceMeter ▶ Multifunction Process Calibrator Fluke 725        Multifunction Process Calibrator Fluke 725 브랜드 : 03   ▷ 간단한 설명   Multifunction Process Calibrator Fluke 725 Measure - volts, mA, RTDs, thermocouples, frequency, and ohms - 상태 : Used,Very Good     Multifunction Process Calibrator   Fluke 724/725 Measurement Accuracy Voltage DC 30.000 V 0.02%+ 2 counts (upper display) 30.000 V 0.02%+ 2 counts (lower display) 100.00 mV 0.02%+ 2 counts -10.00 mV to 75.00 mV 0.025 % + 1 count (via TC connector) Current DC 24.000 mA 0.02%+ 2 counts Resistance 0.0 to 400.0 Ω 0.1Ω (4-wire), 0.15Ω (2- and 3-wire) 401 to 1500 Ω 0.5Ω (4-wire), 1Ω (2- and 3-wire) 1500 to 3200 Ω 1Ω (4-wire), 1.5Ω (2- and 3-wire) Frequency 2.0 to 1000.0 CPM 0.05 % + 1 count 1.0 to 1100.0 Hz 0.05 % + 1 count 1.00 to 10.00 kHz 0.05 % + 1 count Sensitivity 1 V peak-to-peak-minimum Pressure Accuracy from 0.025% of range using any of 29 pressure modules. (for detailed specifications refer to pressure modules in options and accessories) Modules available for differential, gage, vacuum, absolute, dual and high pressure. Source Accuracy Voltage DC 100.00 mV 0.02%+2 counts 10.000 V 0.02%+2 counts -10.00 mV to 75.00 mV 0.025 % + 1 count (via TC connector) Current DC 24.000 mA (Source) 0.02%+ 2 counts 24.000 mA (Simulate) 0.02%+ 2 counts Resistance 15.0 to 400.0 Ω 0.15 Ω (exc. current 0.15 to 0.5 mA), 0.1 Ω (exc. current 0.5 to 2 mA) 401 to 1500 Ω 0.5 Ω(excitation current 0.05 to 0.8 mA) 1500 to 3200 Ω 1 Ω(excitation current 0.05 to 0.4 mA) Frequency 2.0 to 1000.0 CPM 0.05% 1.0 to 1100.0 Hz 0.05% 1.00 to 10.00 kHz 0.25% Waveform: 5 V p-p squarewave, -0.1 V offset RTDs and Thermocouples Measure Accuracy: NI-120 0.2 °C PT-100 (385) 0.33 °C PT-100 (393) 0.3 °C PT-100 (JIS) 0.3 °C PT-200 (385) 0.2 °C PT-500 (385) 0.3 °C PT-1000 (385) 0.2 °C Resolution: 0.1 °C J: 0.7 °C K: 0.8 °C T: 0.8 °C E: 0.7 °C R: 1.8 °C S: 1.5 °C B: 1.4 °C L: 0.7 °C U: 0.75 °C N: 0.9 °C Resolution J, K, T, E, L, N, U: 0.1 °C, 0.1 °F B, R, S: 1 °C, 1 °F XK 0.6°C BP 1.2°C Source Accuracy: NI-120 0.2 °C PT-100 (385) 0.33 °C PT-100 (393) 0.3 °C PT-100 (JIS) 0.3 °C PT-200 (385) 0.2 °C PT-500 (385) 0.3 °C PT-1000 (385) 0.2 °C Resolution: 0.1 °C Note: Accuracy stated for 4-wire measurement. J: 0.7 °C K: 0.8 °C T: 0.8 °C E: 0.7 °C R: 1.4 °C S: 1.5 °C B: 1.4 °C L: 0.7 °C U: 0.75 °C N: 0.9 °C Resolution J, K, T, E, L, N, U: 0.1 °C, B, R, S: 1 °C XK 0.6°C BP 1.2°C Specifications Ramp Functions Source functions: Voltage, current, resistance, frequency, temperature Ramps Slow ramp, Fast ramp, 25% step-ramp Loop Power Function Voltage: 24 V Accuracy: 10% Maximum current: 22 mA, short circuit protected Step Functions Source functions: Voltage, current, resistance, frequency, temperature Steps 25% of range, 100% of range Environmental Specifications Operating Temperature -10 °C to +55 °C Storage Temperature -20 °C to 71 °C Operating Altitude 3000 m Safety Specifications Agency Approvals EN 61010-1:1993, ANSI/ISA S82.01-1994; CAN/CSA C22.2 No 1010.1:1992 Mechanical & General Specifications Size 130 x 236 x 61 mm Weight 0.65 kg Batteries 4 AA alkaline batteries Battery Replacement Separate battery compartment, accessable without breaking calibration seal Side port connections Pressure module connector, also used for remote real-time programming